Jul 25, 2018· Air carbon arc gouging is a process of removing metal by means of heat generated from a carbon arc. The process uses a carbon/graphite electrode, compressed air and a standard power source. The intense electric arc used between the tip of a carbon electrode and a metal work piece cuts and melts the work piece.
May 03, 2016· Plasma gouging works on any conductive metal, including mild steel, stainless steel, aluminum, and copper. With a bit of practice, it is possible to achieve smooth, clean, consistent gouges. Compared to other processes, such as carbon arc gouging, plasma gouging can reduce the amount of noise and debris in the work environment.
The arc voltage used in air carbon arc gouging and cutting ranges from a low of 35 to a high of 56 volts; thus the open-circuit voltage should be at least 60 volts. The actual arc voltage is governed by arc length and the type of gouging. For most applications CAC-A is used with DCEP
Air carbon arc cutting, also referred to as metal arc gouging, and previously as air arc cutting, is an arc cutting process where metal is cut and melted by the heat of a carbon arc. Molten metal is then removed by a blast of air. It employs a consumable carbon or graphite electrode to melt the material, which is then blown away by an air jet. This process is useful for cutting a variety of materials, but it is most often used for cutting and gouging
3.1 Like arc welding, arc carbon air gouging uses an intense arc to create a molten pool on the work piece. The process requires a welding power source, air compressor, carbon electrode, and gouging torch, see figure 3.1 below. Figure 3.1 Air carbon arc setup for general use with DCEP
Nov 21, 2000· Air Carbon Arc Gouging and Cutting, but is included for informational purposes only. These recommended practices have been prepared by the C5 Subcommittee on Air Carbon Arc Gouging and Cutting, of the AWS Arc Welding and Cutting Committee. It is important to recognize that this publication does not present the
ARC GOUGING ELECTRODES. Our CarbonElite™ premium copper coated arc gouging electrodes are designed to maximize metal removal while optimizing melt-off efficiency and arc stability to deliver consistent, high quality performance. Available in pointed, jointed, flat and hollow electrode types for use in a wide range of applications.
Air carbon-arc gouging removes metal through the intense heat of an arc created between a carbon electrode and the workpiece. As the material melts, compressed air, which is directed through outlets in the lower jaws of the torch holding the electrode, lifts the molten metal clear of the arc
Jun 30, 2013· Air carbon-arc gouging began in the 1940s, evolving from the existing carbon-arc cutting process. Myron Stepath, a welding engineer, developed air carbon-arc gouging to remove several hundred feet of flat, cracked, stainless steel weld. Previously, carbon-arc cutting removed overhead and vertical defective welds and rivet heads.
3.1 Like arc welding, arc carbon air gouging uses an intense arc to create a molten pool on the work piece. The process requires a welding power source, air compressor, carbon electrode, and gouging torch, see figure 3.1 below. Figure 3.1 Air carbon arc setup for general use with DCEP
ARC GOUGING ELECTRODES. Our CarbonElite™ premium copper coated arc gouging electrodes are designed to maximize metal removal while optimizing melt-off efficiency and arc stability to deliver consistent, high quality performance. Available in pointed, jointed, flat and hollow electrode types for use in a wide range of applications.
Oct 08, 2019· Carbon arc welding is the term to describe joining metal elements together by using electricity. Whereas other methods use gas to heat the metal and fuse it together, carbon arc gouging relies only on electricity. An electric arc is formed between the
Air carbon-arc gouging removes metal through the intense heat of an arc created between a carbon electrode and the workpiece. As the material melts, compressed air, which is directed through outlets in the lower jaws of the torch holding the electrode, lifts the molten metal clear of the arc
The arc voltage used in air carbon arc gouging and cutting ranges from a low of 35 to a high of 56 volts; thus the open-circuit voltage should be at least 60 volts. The actual arc voltage is governed by arc length and the type of gouging. For most applications CAC-A is used with DCEP (reverse polarity). The electrode should extend at most 7
This item: Arcair 01065001 Extreme K3000 Air Carbon Arc Gouging Torch Medium Duty $243.68 Ships from and sold by A2Z Industrial Distributor, Inc.. 6" x .045 x 7/8" T1 Premium Thin Cut-Off Wheel Metal & Stainless Steel 25 Pack $25.00
POINTED COPPERCLAD DC ELECTRODES A standard, all purpose gouging electrode. Its controlled copper coating improves electrical conductivity (for more efficient, cooler operation) and helps maintain electrode diameter at the point of the arc. POINTED PLAIN DC ELECTRODES General purpose electrodes without the copper plating to avoid any chance of copper contamination in the base material.
POINTED COPPERCLAD DC ELECTRODES A standard, all purpose gouging electrode. Its controlled copper coating improves electrical conductivity (for more efficient, cooler operation) and helps maintain electrode diameter at the point of the arc. HOLLOW POINTED COPPERCLAD DC ELECTRODES General purpose electrodes having the same high quality blend of carbon and graphite used in other
Apr 29, 2006· Maybe carbon arc gouging is one of those things where it's very important to have at least the minimum air pressure and volume required while having extra doesn't hurt and probably helps. Hawk's suggestion that 13+ cfm would be enough jives with the Thermadyne web page recommendation and gives me some confidence I can come up with enough air
Sep 13, 2009· At 200 amps your going to be limited to a 3/16 carbon arc-rod at 40-80 lbs of air pressure,but you can always use a bigger air carbon gouging torch.I have 3 1000 amps running 5/16 and 3/8 carbon arc rods at 425-450 amps.Look at airgas Randor brand there cheap and are good
Carbon-arc gouging is a melting operation, where metal is removed from the surface by the arc pressure or force. Direct current (DC) is used and the electrode is graphite coated with a layer of copper to assist conductivity. Most materials may be gouged by
May 09, 2006· Gouging—a requirement for many years in several industries and applications—is one method to scrutinize. Especially in maintenance and repair, the ability to gouge or groove metal is critical and deserves proper consideration. Two of the most common methods of gouging metal are plasma gouging and air carbon-arc gouging.
Jun 08, 2004· Air Carbon Arc Gouging. In the air carbon arc process, an electric arc is generated between the tip of a carbon electrode and the metal workpiece. A jet of air is directed around the tip to remove molten metal from the area, forming a groove. Air carbon arc gouging can be used on mild steel, cast iron, nickel alloys, copper, and aluminum.
This high quality carbon arc gouging torch leads the pack with rugged construction and reduced weight to minimize fatigue. Features include: Accepts up to 1/2in diameter jointed carbons. Natural 15 degree torch angle for operator comfort. 360 swivel cable reduces cable twist. Positive grip
ARC GOUGING ELECTRODES. Our CarbonElite™ premium copper coated arc gouging electrodes are designed to maximize metal removal while optimizing melt-off efficiency and arc stability to deliver consistent, high quality performance. Available in pointed, jointed, flat and hollow electrode types for use in a wide range of applications.
Oct 08, 2019· Carbon arc welding is the term to describe joining metal elements together by using electricity. Whereas other methods use gas to heat the metal and fuse it together, carbon arc gouging relies only on electricity. An electric arc is formed between the
Carbon Arc Gouging; Manual Torches & Cables. Automatic Gouging / Travel Systems. Carbons. 1-800-ESAB-123 . Contact us Find a distributor By product line. Arc Welding Equipment; Cutting Automation; PPE & Accessories; Plasma; Filler Metals; Gas Equipment; Arc Gouging (CAC-A) & Exothermic Cutting; Welding Automation & Robotics;
Carbon Arc Cutting (CAC), also known as metal arc gouging or air arc cutting, is a metal cutting method that uses high temperature to heat a metal to its melting state. Here, the heat is generated by a carbon electrode arc. The molten metal is blown off by a high-velocity jet of compressed air.
The arc voltage used in air carbon arc gouging and cutting ranges from a low of 35 to a high of 56 volts; thus the open-circuit voltage should be at least 60 volts. The actual arc voltage is governed by arc length and the type of gouging. For most applications CAC-A is used with DCEP (reverse polarity). The electrode should extend at most 7
POINTED COPPERCLAD DC ELECTRODES A standard, all purpose gouging electrode. Its controlled copper coating improves electrical conductivity (for more efficient, cooler operation) and helps maintain electrode diameter at the point of the arc. HOLLOW POINTED COPPERCLAD DC ELECTRODES General purpose electrodes having the same high quality blend of carbon and graphite used in other
the speed of air carbon -arc gouging is much faster than shielded metal arc welding, friction between the gloved hand and the work piece may cause a jerky forward motion, This motion causes the gap between the electrode and work piece to become too large to maintain the arc
Jun 20, 2013· Re: Carbon-Arc Gouging (Video) If you are doing a lot of arc air gouging you should use an overly large welder. 250 amps is bare minimum. Most shops use a 400 or 500 amp machine or if they have it a 1000A Gouging is very hard on the transformers. Use constant current if possible.
Sep 13, 2009· At 200 amps your going to be limited to a 3/16 carbon arc-rod at 40-80 lbs of air pressure,but you can always use a bigger air carbon gouging torch.I have 3 1000 amps running 5/16 and 3/8 carbon arc rods at 425-450 amps.Look at airgas Randor brand there cheap and are good
Jul 24, 2019· Trouble is, the mainstream carbon arc gouging holders are way big for hobbyists like CEP and I. They are for high amperage and require massive amounts of air. There are some smaller, but seem more expensive than the big ones last time I looked. I'd like to have a little 250 Amp holder for delicate work like cataract surgery
The arc voltage used in air carbon arc gouging and cutting, ranges from 35-55 volts. An open circuit voltage of at least 60 volts is required. The actual arc voltage in air carbon arc gouging and cutting is governed to a large extent by the size of the electrode.
Jun 08, 2004· Air Carbon Arc Gouging. In the air carbon arc process, an electric arc is generated between the tip of a carbon electrode and the metal workpiece. A jet of air is directed around the tip to remove molten metal from the area, forming a groove. Air carbon arc gouging can be used on mild steel, cast iron, nickel alloys, copper, and aluminum.
May 09, 2006· Gouging—a requirement for many years in several industries and applications—is one method to scrutinize. Especially in maintenance and repair, the ability to gouge or groove metal is critical and deserves proper consideration. Two of the most common methods of gouging metal are plasma gouging and air carbon-arc gouging.
Recommended / Intended use: Carbon Arc Gouging Unique Reference Numbers Arc Air Gouging Carbons. 2-GC5, 2-GC65, 2-GC8, 2-GC95, 2-GC13 Composition These electrodes consist of solid graphite rods coated with a protective copper coating, manufactured in short lengths and supplied in packages. APPROXIMATE COMPOSITION OF CARBON GOUGING ELECTRODES (WT %)